Woodpecker RTA Intelli-Sensor RVG by Waldent – Size 1.5

The Woodpecker RTA Intelli-Sensor RVG by Waldent – Size 1.5 is a digital intraoral radiography sensor designed to capture dental X-ray images and display them through compatible imaging software on a computer. It provides a digital alternative to conventional dental X-ray film, supporting image acquisition and storage within a digital dental workflow.

Featuring CMOS sensor technology, a 24 × 33 mm effective imaging area, and a 20 μm pixel size, the sensor is designed to capture detailed radiographic images of teeth and surrounding structures. Its Size 1.5 format is particularly useful for pediatric patients, smaller oral cavities, and selected anterior imaging procedures where a compact sensor may be preferred.

The sensor has a slim 4.5 mm profile with curved edges to facilitate intraoral placement. Its flexible 2.7 m USB cable supports convenient positioning during radiographic examinations. The IP68-rated sensor construction provides protection against dust and water ingress under the conditions specified for the device.

The accompanying imaging software is designed for compatible Windows-based computers, allowing captured radiographs to be viewed and managed digitally. The system can support routine intraoral radiography for caries assessment, periapical evaluation, endodontic treatment planning, periodontal assessment, and other diagnostic applications when used with an appropriate dental X-ray generator.

The Woodpecker RTA Intelli-Sensor Size 1.5 is suitable for dental clinics, hospitals, and dental colleges seeking a digital intraoral imaging solution for routine dental radiographic procedures.

• CMOS digital radiography sensor designed for capturing intraoral dental X-ray images.

• Size 1.5 sensor format suitable for pediatric radiography, patients with smaller oral cavities, and selected anterior imaging applications.

• High-resolution imaging with a stated theoretical resolution of 25 lp/mm.

• Effective resolution greater than 12 lp/mm, according to the product specifications.

• Ultra-thin 4.5 mm sensor profile designed to support comfortable intraoral positioning.

• Effective imaging area of 24 × 33 mm for capturing detailed dental radiographs.

• IP68-rated protection against dust and water ingress.

• Flexible 2.7 m USB cable for convenient positioning and connection to a compatible computer.

• Durable cable design tested for more than 80,000 bending cycles, as specified in the product information.

• Rounded, curved sensor edges designed to improve patient comfort during positioning.

• Dedicated Windows-compatible imaging software for image acquisition and management.

• Digital image capture supports clinical assessment, treatment planning, endodontic evaluation, and diagnostic documentation.

• 1 × Woodpecker RTA Intelli-Sensor RVG – Size 1.5

• 1 × Disposable Protective Bag

• 1 × Sensor Fixer

• 1 × Anti-Counterfeiting Query Label

• 1 × USB Drive (U Disk)

• 2 × Fixing Screws

• 2 × Rubber Stoppers

• 1 × Certificate of Conformity / Qualified Certificate

• 1 × Warranty Card

• 1 × Instruction Manual

• Product Name: Woodpecker RTA Intelli-Sensor RVG by Waldent – Size 1.5

• Brand: Woodpecker / Waldent RTA

• Product Type: Digital Intraoral Radiography Sensor

• Sensor Technology: CMOS

• Sensor Size: 1.5

• Effective Imaging Area: 24 × 33 mm

• Mechanical Dimensions: 43.5 × 29.2 × 4.5 mm

• Pixel Size: 20 μm

• Pixel Matrix: 1200 × 1650

• Theoretical Resolution: 25 lp/mm

• Effective Resolution: Greater than 12 lp/mm

• Sensor Thickness: 4.5 mm

• Cable Length: Approximately 2.7 m

• Interface: USB

• Power Supply: 5 V / USB Interface

• Water and Dust Protection: IP68

• Cable Durability: Tested for more than 80,000 bending cycles, as specified

• Electrical Protection: BF-Type Applied Part

• Operating Mode: Intermittent

• Supported Operating System: Windows 7 or above

• Recommended Processor: Intel Core 4 or above, as specified

• Recommended Memory: 8 GB RAM or above

• Recommended Hard Drive: 500 GB or above

• USB Ports: 4 high-speed USB 2.0 ports, as specified

• Supported USB Chipsets: Intel or NEC / RENESAS

• Recommended Display Resolution: 1920 × 1080 pixels

• Operating Temperature: 10°C–35°C

• Operating Humidity: 20%–90%

• Atmospheric Pressure: 70–106 kPa

• Primary Applications: Intraoral Dental Radiography, Periapical Imaging, Caries Assessment, Endodontic Evaluation, and Periodontal Assessment

1. Confirm that the computer meets the recommended system requirements and runs a compatible Windows operating system.

2. Install the designated Woodpecker RTA Intelli-Sensor imaging software using the supplied installation media and follow the manufacturer’s installation instructions.

3. Connect the RVG sensor to a compatible USB port and complete the software setup.

4. Verify that the imaging software recognizes the sensor before beginning a radiographic procedure.

5. Cover the sensor with a new, suitable disposable protective barrier for each patient.

6. Position the sensor intraorally using an appropriate holder and positioning technique for the required projection.

7. Position the compatible dental X-ray generator according to the intended radiographic view and follow radiation-safety procedures.

8. Select the appropriate exposure settings according to the X-ray generator’s instructions, the patient’s needs, and the clinical indication.

9. Acquire the radiographic image and review it using the designated imaging software.

10. Save the radiograph to the appropriate patient record and verify that the image is correctly stored.

11. After the procedure, remove and discard the protective barrier according to infection-control procedures.

12. Clean and disinfect the sensor surface according to the manufacturer’s instructions. Do not assume that IP68 protection makes the sensor suitable for immersion or autoclaving.

13. Handle the cable carefully and avoid sharp bends, pulling, crushing, or twisting during use and storage.

14. Store the sensor securely in its designated holder when not in use.

• Warranty: 5 Years Manufacturer/Importer Warranty, as applicable.

• Physical damage to the product is not covered under warranty.

• Handle the sensor and cable carefully to prevent damage to the sensor housing, cable, and USB connection.

• Use a suitable disposable protective barrier for each patient and follow the manufacturer’s cleaning and disinfection instructions.

• Do not autoclave the sensor unless expressly permitted by the manufacturer.

• Use compatible software, computer hardware, and USB connections according to the specified system requirements.

• Keep the sensor away from excessive heat, impact, and improper handling.

• Retain the purchase invoice and warranty card for service and warranty claims.

• Warranty claims are subject to the applicable manufacturer/importer terms and conditions.